Just How to Remove as Well as Replace a Bath Tub
Just How to Remove as Well as Replace a Bath Tub
Blog Article
Do you find yourself on the lookout for critical info concerning Tools You Need to Install a New Bathtub ?
Mounting a tub isn't specifically rocket science, yet it does require strong plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately hard project. If the old bathtub is conveniently available, the task can move immediately; if you need to open a wall surface to get rid of the old tub as well as place the brand-new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will need a helper to vacate the old bathtub and set in the brand-new one. Make sure you have certified on your own for the job and fit trying it. Rather than hiring a specialist to take control of a halfway-completed project, it is better to think about utilizing one prior to you start. Chances are you may need a professional plumber to make tube connections.
This post will assist you set up a brand-new bath tub in your bathroom if you have already gotten a brand-new bathtub and also do not need to change the arrangement of your previous supply of water pipelines.
Your devices and also product list must make up the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, switch on the taps to drain any water staying in the system. The process of getting rid of the existing faucets can be fairly bothersome as a result of the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipelines have actually been eliminated, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from transforming during this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing substance.
Before moving on to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making sure that the washers remain in place in between the tap and also the sink. Protect the tap in position with the producer provided backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type needs to be connected to the faucet ends initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Utilizing both wooden boards under its feet, position the tub in the called for position. The wood boards are useful in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the tub till the spirit level reviews level.
To set up faucets, fit the bottom of the furthest adaptable tap port to the ideal supply pipe by making a compression sign up with; then do the exact same for the other faucet.
Activate the supply of water as well as examine all joints and new pipework for leakages and also tighten them if required. Fill up the tub as well as also inspect the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, fix the bath paneling as explained in the maker's user's manual. Tiling and sealing around the tub needs to wait till the bathtub has been utilized at the very least when as this will settle it into its final setting.
Planning for the Installment
To start with, the sustaining structure provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to avoid stress on the tub.
Fit the versatile tap adapters to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use all of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must now be ready to be suited its last setting.
Tiling Around the Tub
In the area where the bathroom satisfies the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to break an inflexible seal, creating the water to penetrate the wall surface between the bath and the tiling, causing complications with dampness as well as feasible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to allow for the activity experienced when the bathtub remains in use. The sealer can break rather early if you do not take into account this motion before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the market. It is a good idea to fit the tiles utilizing waterproof or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very intrigued by Tools You Need to Install a New Bathtub and I hope you enjoyed my piece. For those who enjoyed our article please be sure to pass it around. Thank-you for going through it.
Schedule Your Job Now
Report this page